Push the release lever forward and rotate the key towards you until it stops. No additional vehicle service is required. Foglamp control if equipped The headlamp control also operates the foglamps. Curb weight seems to be the determining factor with these trucks. Remove particles such as bird. The jack handle ratchets when the tire is raised to the stowed position.
When in this position rotate the control upward for fast intervals and downward for slow intervals. Make a further check for leaks in the fuel system. This position should only be used when towing the vehicle. Wet brakes do not stop the vehicle as effectively as dry brakes. Treadwear The treadwear grade is a. Do not use extensions to change the fit of the shoulder belt across the torso. To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire.
The readiness light will not illuminate immediately after ignition is turned on. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle. I actually just replaced the slave cylinder in this truck a week or two ago for the current owner of this truck and noticed the rather puny looking clutch, thinking to myself that this may well be the reason for the low towing capacity. Loosen each wheel lug nuts one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Block the diagonally opposite wheel.
If starting a vehicle with a manual transmission: Make sure the parking brake is set. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. The front wheels are prevented from locking even when the brakes are firmly applied. Would you please help me out and tell me the typ and qty i'm gonna need thank you. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Cars with automatics have to slow down suddenly because I'm trying to get into second gear without clashing the gears anymore than necessary.
I am considering purchasing a 1998 Ford F-150 with a manual transmission. Once the engine has been started, run both vehicles for a further three minutes before disconnecting the leads. They are strongly recommended if you live in a region where temperatures reach -23°C -10°F or below. To begin this process: 1. The price was very good for the low mileage. Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Reverse Make sure that your vehicle is at a complete stop before you shift into R Reverse. Do not tow with slingbelt equipment. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. Torque 3000 rpm Required fuel 87 octane grade Firing order 1-4-2-5-3-6 1. They first told me the battery needed to be charged, I started couldn't you put in a new battery. Trailer lamps Trailer lamps are required on most towed vehicles.
Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. Engine oil pressure gauge This shows the engine oil pressure in the system. Refer to Automatic locking mode. This 2 door, 3 passenger truck provides exceptional value! Make sure that the seat is relatched into place.
Never adjust the steering wheel when the vehicle is moving. Is the transmission in this truck really weak? Autolock This feature automatically locks all doors when:. This 2 door, 3 passenger truck has not yet reached the 50,000 mile mark! Within two seconds of pressing the washer control, put the key in the ignition. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. A confirmation sequence of tones will sound. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.
Maybe that explains the price. Store the center safety belt in the opening on the seat back. Press the control to move the seat forward, backward, up or down. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Install the child safety seat in a seating position which is capable of providing a tether anchorage. The bars of varying length are for intermittent wipers.