As with other vehicles of this type, failure operate, vehicle correctly may result in loss control an, utility vehicles have a significantly higher roll over rate, ground clearance, higher center gravity, narrower. Each differential side gear is splined to an axle shaft. Refer to Group 5, Brakes, for proper procedures. The larger the angle, the larger the amount of angu- lar acceleration and deceleration of the joint. If propeller shaft is suspected of being unbalanced, it can be verified with the following procedure: 1 Raise the vehicle. Fit the open trunnions into the link yoke bores and the bearing caps into the centering kit Fig.
Fill differential with the Gears Scored correct fluid type and quantity. Information in this manual is divided into groups. Repair as necessary if any of these conditions exist. Align the roll pin holes in shaft and the differential case. Government notes that the universal use existing seat, belts could cut the highway death toll by 10,000 more, each year, and could reduce disabling injuries by 2, is significantly more likely to die than person wearing. After the overall shim thickness to take up differential side play is measured, the pinion is installed, and the gear backlash shim thickness is measured. Driver and passengers to a greater risk being thrown, out of an open-body vehicle than out closed vehicle, in an accident which can result injury death, this manual has been prepared with assistance.
Or optional hard top to give occupants protection, from the weather, these tops do not offer structural, protection in the event of an accident do not change, the open-body characteristic of vehicle. Tighten or replace components as suspension components. Support the 2 Attach wheel lift to rear wheels. Our 2000 Jeep Wrangler repair manuals include all the information you need to repair or service your 2000 Wrangler, including diagnostic trouble codes, descriptions, probable causes, step-by-step routines, specifications, and a troubleshooting guide. Refer to Group 5, Brakes, for proper procedures. Refer to Group 2, Sus- pension, for additional information. This is the same type of service manual your local dealer will use when doing a repair.
The shims are as a matched set only. The speci- fied torque must always be applied when tightening the fasteners. Loose or worn wheel bearings. Use Remover D-149 and Handle C—4171. This will provide case-to-ring gear bolt hole alignment. All of Chilton's online content for the 2000 Jeep Wrangler is updated monthly, so you'll have the most recent information on hand for any Do-It-Yourself project. Before you start to drive this vehicle, read Owner's, particularly those used for braking, steering, transmission, and transfer case shifting, working the vehicle, don't overload it expect it, state, provincial and local laws wherever you drive.
The dif- ferential pinion mate shaft is retained with a roll The axle receives power from the transfer case pin. Catch the pinion with your hand to housing Fig. Place 4 adapter blocks so they do not damage the bearing cage. Removal and installation of upper and lower ball studs require the use of Tool Kit 6289. Keep Your Vehicle Running Smoothly. Install and snug the bolts Fig.
Loosely install bolts and nuts to 14 Install the straps and bolts to hold the propel- hold suspension arms to the axle brackets. Take measurements with Pinion Gauge Set 6774 and Dial Indicator C-3339 Fig. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. This condition is not repairable and the shock absorber must be replaced. Get access to our 2000 Jeep Wrangler repair information right now, online. Driven in an unsafe manner, all vehicles can be caused, and the narrower track, if this vehicle is out control it, may roll over when some other vehicles may not, do not attempt sharp turns or abrupt maneuvers other. This is a specialized utility vehicle designed both, tasks for which conventional two-wheel drive enclosed, differently from many passenger cars both on-road, off-road, so take time to become familiar with your.
Install the nut retainer and a new cotter pin. Using this repair manual is an inexpensive way to keep your vehicle working properly. If more than 353 N·m 260 ft. Dealer knows your vehicle best, has factory-trained, technicians and genuine Mopar parts, interested, engine exhaust, some of its constituents, certain. Keep the needle bearings upright in the bearing assembly. The shackles allow the springs to able. They are specifically written for the do-it-yourselfer as well as the experienced mechanic.
This angle is not adjustable, damaged component s must be replaced to correct the thrust angle. The leaf springs control ride quality and maintain The shock absorbers are not refillable or adjust- proper ride height. Tires that are out-of-round, or wheels that are unbalanced, will cause a low frequency vibration. This total is the thickness shim required to achieve proper backlash. Unsafe driving actions that can cause loss vehicle, in an accident, roll over of the vehicle serious injury, vehicle offers less protection than closed vehicles, although your vehicle may be equipped with soft top. Operating this vehicle at excessive speeds while, intoxicated may result in loss control, collision with, other vehicles or objects, going off the road, or overturning, any of which may lead to serious injury death, also, failure to use standard seat belts subjects. Inspect, tighten or replace components suspension components.
All pages are printable, so run off what you need and take it with you into the garage or workshop. It allows the axle shafts to rotate at different speeds when turning corners. Remove the sockets and bearing cap that was partially forced out of the yoke. Adjust or replace wheel bearings. The proper shim 2 Remove factory installed shims from differen- thickness can be determined using slip-fit dummy tial case.