That means rough idle and poor engine shakes. It would seem the belt would self-adjust on start-up and I really don't want to go in again. Here at Advance Auto Parts, we work with only top reliable Serpentine Belt product and part brands so you can shop with complete confidence. You don't have to remove the tensioner pulley or anything. Secure the new pulley to the engine block by bolting it in place using the old bolts, a socket and the ratchet. It uses 2 of different sizes.
I did not say this was a simple job. Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move. The drive belt controls the power steering pump. Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move. The coils in the front are not too bad but the coils in the rear 3 cylinders means that you need to remove the intake and numerous wires and hoses. This will show an illustration for the proper 2000 Nissan Maxima serpentine belt replacement route around the engine. Hope helps remember to rate and comment this answer.
Not sure how it didn't fail? The black flasher is located out the right side of the fuse access panel at the driver's left knee, towards the steering wheel. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. As those who have already done this know, tensioning is done via a spring loaded idler so no belt adjustment is necessary. The fuse is located either under the dash or in the engine department. Use the information in this video at your own risk. Once the belt is tight, push down on the belt with the palm of your hand.
The serpentine belt is tensioned by an adjustment pulley between the alternator and the crankshaft. I am personally going back to answer your unanswered questions. If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Then you'll see the flasher. Look at the tensioner and insert the tool into it and apply opposing pressure to release the belt. Then you can take the belt off.
Replace the belt and reverse the procedure to tighten the new belt up. This could cause excessive heat in the serpentine belt and cause the belt to snap. Jul 13, 2011 if the mechanic by-passed the belt for what reason was it -? The diagram shows you where the idler pulley is located. The belt tensioner has a belt length indicator. Jack up right front of car. Returning it as soon as I have time to waste going to the store once more. Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley.
The repair is now complete. Always gotta be suspicious of a poster who doesn't know a 4 from a 6. The next step for 2000 Nissan Maxima serpentine belt replacement is simply removing the old belt from around the various pulleys. Turn the wrench handle, the pulley moves and the tension on the belt slackens. The known issue with Maximas is that the ignition coils tend to go bad typically around 70-90,000 miles. This Driveworks belt has been constructed and engineered to meet the stringent demands of today's automotive drive systems. Shop online, find the best price on the right product, and have it shipped right to your door.
A lo … ng box wrench works the best to get it loose. Slide Alternator down and forward to remove. Here's what I did: 1 get the right side up on a jack stand and pull the wheel. The belt I removed looked pretty good. Answer - Loaction of 2000 Nissan Maxima. The repair is now complete. Sorry it took so long.
My sincere apologies for the delayed response. This movement is the tensioner self-adjusting and is required to maintain constant belt tension. Print out a diagram of your belt system. It's easy to get off a rib, so check carefully. Such as, safety glasses, jack stands, no loose clothing, etc. It us under the hood to the right of the battery labeled once you remove the fuse box cover and yes there i … s a fuse puller under the dash. Wiring diagram nissan maxima 2000 wiring diagram de 2000 nissan maxima engine wiring diagram parts exhaust system 2000 nissan maxima ignition key wiring diagram nissan maxima 2000.
When it comes to your Nissan Altima, you want parts and products from only trusted brands. You may want to Print the Diagrams for future use. The serpentine belt controls the air conditioner pump and the alternator. The serpentine belt is located on the front of the engine block and winds around several pulleys driving various engine components: water, fuel and power steering pumps, the alternator, air conditioner compressor and possibly other accessories. How hard was is for you to get the new belt on? I believe it is a 12 mm head. It's a hard pull, so you may want a short cheater on your wrench. To the left of the power steering pump is a long bolt running up and down with the head on the bottom of the bolt.
The front belt is a serpentine belt. No wonder things looked different when I went in! Drive belt slack is taken up by the automatic tensioner. The search can sometimes be hit or miss depending on the wording you use; doesn't help when one thing has a bunch of different names like in this case. Now, simply install the new belt making sure it fits into the grooves on all the pulleys. You usually … see a Check Engine Light which generally means a diagnostic code has been set in the car's computer monitoring. Find the tension pulley located at the bottom of the motor. When that happens, the car runs rough idle and even sometimes stalls.